Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
Were you on the lookout for critical info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly brain surgery, however it does need strong plumbing, carpentry, and often, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult project. If the old bathtub is conveniently easily accessible, the task can relocate speedily; if you have to open up a wall to get rid of the old bathtub as well as position the new bath tub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the brand-new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you begin. Chances are you might require a specialist plumber to make tube connections.
This article will certainly aid you mount a new bathtub in your shower room if you have actually currently acquired a brand-new bathtub and also do not require to alter the plan of your previous water pipelines.
Your tools as well as material checklist should comprise the following:
Getting ready for the Installment
Firstly, the sustaining structure provided with the bathroom should be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to prevent stress on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth all set for the remaining water that will originate from the pipes. When the supply pipelines have actually been removed, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single faucets from transforming throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before carrying on to fit the new taps, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Using both wood boards under its feet, position the bath tub in the needed position. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and changing the feet on the bathtub until the level reviews degree.
To set up faucets, fit all-time low of the furthest flexible tap port to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Turn on the water supply and check all joints and brand-new pipework for leakages as well as tighten them if needed. Load the bathtub as well as likewise check the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bathtub should wait up until the tub has been made use of a minimum of when as this will resolve it into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers remain in place in between the faucet and also the sink. Protect the tap in place with the maker provided backnut. Once the faucet is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The previous type ought to be attached to the faucet ends initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and also can securing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to permit the motion experienced when the tub is in use. The sealer can fracture fairly very early if you do not consider this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily available on the marketplace. It is advisable to fit the floor tiles making use of waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that report about Tools You Need to Install a New Bathtub from someone on another web blog. If you please set aside a second to share this content if you appreciated it. Thanks a bunch for your time. Visit again soon.
Schedule Your Job Now Report this page